• There has been a recent cluster of spammers accessing BARFer accounts and posting spam. To safeguard your account, please consider changing your password. It would be even better to take the additional step of enabling 2 Factor Authentication (2FA) on your BARF account. Read more here.

Big bore kit on CR250R

StrictlyHonda

New member
Joined
Oct 8, 2008
Location
San Jose, CA
Moto(s)
02 CR250, 06 CRF450R
Name
Steve
I need to rebuild my top end. I messed up the cylinder, head, and piston. I have found pricing on rebuilding it to stock with a new sleeve and it is only a little more to Put a big bore kit on it and bore it from 250cc to 270cc. My Question is: has anyone done a big bore kit on there CR250 and would you recommend it? I am wondering if I am going to have major problems with overheating and also if i am going to need to do any other mods in order for the bike to run great, such as change carb or jetting. Also will this totally mess up the reliability of my Cr250?

Thank you for your advice.
 
adding only 20cc to the motor won't hurt reliability. if you went to the 310 or 330 kit you might have some problems. you'll need to rejet, but thats about it.
 
+1
I put a LA sleeve big bore kit (250 to 280) in a kx250 I had. It ran great without any problems. (raced it for 2 years before selling it)
 
Awesome thank you. How easy was it to get a 280cc rebuild kit? and was it more expensive.



It's easy to get the kit, there are a few aftermarket companies that offer them (LA sleeve being one). The expensive part is the machining involved. The cylinder needs to be bored, then the sleeve pressed in and bored for the new piston then the ports need to be matched. In my case, it was cheaper than buying a new cylinder because I'm a machinist and did the work myself:teeth. I know there are companies that do all the work if you just send them your old cylinder....not sure about the cost though.
 
found the big bore kit though LA Sleeve and it is $520 for a 270cc. I have been pricing cyclinders and the cheapest cylinder that i have found is $375 from cheaphondaparts.com I will try to find the IIRC cylinder you are talking about.
 
I have priced it out and it is as follows:
Cylinder- $335
Head- $70
Piston kit with gaskets and everything- $120
total- $525 plus tax

The big bore kit is $520, so it is not much of a difference. I would put the bike to stock if i could get all parts for lets say $350 or $400. I am still working on funds right now while trying to make u my mind.
 
isn't the big bore kit an iron lined cylinder?? that would mean you can use over bore piston sizes when the cylinder wears. with the stock set up you'll either have to replace/replate/resleeve the cylinder when the coating wears off. i think in the long run the big bore or iron lined cylinder will be cheaper and easier to deal with.
 
You are correct. In my case the only option i have with a 02 CR250R is to resleeve. So i would have to re-sleeve either way. whether i was to go back to stock or add the big bore kit.. I believe that my cylinder is magnesium so there is no option of just boring it out.
 
No it's not magnesium. (I think the only significant magnesium on your bike is its clutch cover.) Replating the cylinder is an option.

Just be sure to check replacement costs for the big bore piston before you decide. I know one of the YZ250 kits (285cc?) has a single source for replacement pistons and they are outrageously expensive.
 
I actually found a guy locally who will be able to fix it.. The Shop is called Nor-Cal Motorsports. You were right, maybe i took it to the wrong type of shop. Anyway this guy specializes in building motors, so think i am in good hand. I talked me out of the big bore kit because he said i would have to change out the stock crank because it would not be able to handle it. I am still waiting for him to get a quote. i am hoping that is will be cheaper than LA Sleeve. I will let you guys know the updates.
 
for the 270 kit you wouldn't need to change out the crank or do anything else to the bottom-end, as long as it is in good shape to begin with.... the 320 or 370 kit yes, most certainly its a good idea, but its not needed with the 270. however if you want the cheapest, best long-term way to fix it,.... then just get it sleeved with a iron liner & a fresh top end, back to stock bore.... the whole thing. piston, rings, wrist pin, upper rod/top-end needle bearing, circlips, all gaskets & maybe even some of the power valve parts, depending upon inspection.
 
I actually found a guy locally who will be able to fix it.. The Shop is called Nor-Cal Motorsports. You were right, maybe i took it to the wrong type of shop. Anyway this guy specializes in building motors, so think i am in good hand. I talked me out of the big bore kit because he said i would have to change out the stock crank because it would not be able to handle it. I am still waiting for him to get a quote. i am hoping that is will be cheaper than LA Sleeve. I will let you guys know the updates.


The stock crank can handle it just fine....might want to find ANOTHER guy!
 
So the update is that i have a cracked exhaust bridge and intake bridge. so he recommended a new cylinder, which was $365. and he machined my head to get the nicks out of it. all said and done the quoted cost with labor included is about $600, for the whole top end rebuild. he is also going though my bottom end to make sure everything is ok before he puts the top end on and also checking my jets to make sure they are the right size and they are not clogged.
 
So what happened to your bike that caused all that damage?

Were the nicks in the head from detonation or from broken parts?

You might as well have him tighten up the squish clearance while he is working on it. (It's cheap.) That generation CR250 is known to have too much (like most bikes I guess). Using a thinner head gasket barely helps.
 
It was caused by neglect. knew for a while that i had to change my top end and was actually planning on changing it when while i was riding in Hollister I broke the Rings on the piston and parts of the ring got above the piston and nicked my head quite a bit. There were also big scrapes on the cylinder walls as well as a cracked exhaust bridge and intake bridge. So i am buying a stock cylinder and had the head re-surfaced. He is also going to go though the motor and make sure everything is in spec and check my jetting.
 
Back
Top