• There has been a recent cluster of spammers accessing BARFer accounts and posting spam. To safeguard your account, please consider changing your password. It would be even better to take the additional step of enabling 2 Factor Authentication (2FA) on your BARF account. Read more here.

working title: gl1000

I’ve always preferred the original comstars over the reversed despite the smaller size.
 
as hoped, parts bike runs and is indeed in better shape than the donor engine. thanks to some very sage advice from the ignition vendor, that still supports discontinued products! and a little fettling with the clutch the bike runs and can be ridden. Carbs need some tuning for sure, it pops on deceleration and under load, think 2nd gear roll on from ~15mph

my kids like to sit on whatever bike i'm working on and both want to ride with me. they're a little young, and i don't like riding with passengers (i'm not comfortable with it, lack of experience) but the 4 year old actually helped with some electrical diagnosis by holding the multimeter leads, and the nearly 9 year old... well he's just awesome so when it was time to put the bike away they helped me ride it the 50 feet to the back of the driveway. so fun.

[YOUTUBE]sJyp1s1TXes[/YOUTUBE]

the unfortunate part is i finally checked dmv fees. not exactly non-op, $1k due. seller still responding so maybe he has proof of non op somewhere. if not and dmv doesn't play nice i may end up stealing the engine for the other, actually is on non-op, afterall
 
Last edited:
Should I update this thread?
Should I keep trying to finish this bike in the spirit of Dirtbag?

3 YEARS after the last update and some significant life changes (none bad) I'm back working on the original engine that should be in the bike. The "seized" engine from the beginning. Turns out it wasn't stuck rings it was stuck stator/rotor from being rusted together. How exactly that happened I don't know.

The starter clutch, a part married to the rotor and a pretty penny from Honda, reasonably priced on eBay, is also rusty and dead.

One of the clutch friction plates is also nearly stripped of the friction material and the pile I found in the sump isbt ALL of it. To me this means the cases have to be split to clean all that out and I'm just not willing to do that.

That said, this engine could power something with lesser consequences when the engine seized from oil starvation when that clutch material clogs something up. A big go-kart. Gold cart. Wood splitter? Snow blower?

Anyway. Time to get the frame finished, same for the front end swap, and get to getting things finished(ish)

Hopefully the next update is sooner than 3 years
 

Attachments

  • PXL_20260511_191908822.jpg
    PXL_20260511_191908822.jpg
    3.1 MB · Views: 3
  • PXL_20260511_191732368.jpg
    PXL_20260511_191732368.jpg
    4.1 MB · Views: 3
I knew a guy who had an old Wing. He turned it into a cafe racer. It was a beautiful bike. Complete with paint and clip ons.

I also used to know another guy who attached a side car to his Wing. He used to take his black Lab in the side car. The only downside was the dog would occasionally take a dump in it.
 
Last edited:
Now you're just taunting me
I've always wanted to build a ridiculous snow blower. While this thread is only 16 years old I distinctly remember reading about this machine at least 25 years ago... Basically right after all gore invented the internet

 
Anyone checked the prices on replacement antique Honda parts? The valve that made all these dents in the seat is $30+. For 1

This is definitely going to be a lawnmower engine if it ever runs again
 

Attachments

  • PXL_20260515_215600847.jpg
    PXL_20260515_215600847.jpg
    3 MB · Views: 4
Back
Top